Samsung washer 4C or no fill: safe checks
Separate a real 4C/4E/nF no-fill from sensing delay, then check water, hoses, drain and accessible screens.
What this guide covers
Error codes: 4C, 4E, NF · Symptoms: Won’t fill / filling very slowly
This guide follows a structured decision tree built from manufacturer troubleshooting information. It does not assume that the most commonly replaced part is the failed part, and it does not show an exact-fit replacement part unless model compatibility has been independently verified.
Continue this exact diagnostic
Samsung top-load: 4C versus sensing delay
WA50R5400AV/US is top-load. Preserve the exact 4C/4E/nF code and distinguish true no-fill from a short weight-sensing delay or low visible water level before checking hoses, drain installation and accessible screens.
Observe a complete normal startup before reporting success or failure. Shut off water and disconnect power before any owner-approved hose or screen access; stop for a leak near electricity, damaged wiring, unsafe access or a stuck valve. A recognized model does not certify an exact procedure or part.
Work through the Samsung fill checks
Compare washer no-fill paths · Panel dark or cycle will not start?
How to check without guessing
General manufacturer guidance. Exact-model controls and procedures have not been verified for this guide.
General manufacturer guidance only. A recognized model is an identity match, not proof that every control or procedure applies. Stop for active leaking near power, smoke, shock, damaged wiring, repeated breaker trips, or unsafe access. Never perform energized internal tests.
Separate a fill fault from normal sensing
The WA50R5400AV/US benchmark is top-load. Record the actual 4C/4E/nF display before resetting. Samsung says weight sensing may delay visible fill; low water level alone belongs to a different symptom.
Let the normal sensing phase finish
Allow the selected cycle to finish its normal sensing phase without repeated cancel/start actions. Record whether water enters and whether a code appears; a pending observation is not a failure.
Start with the water supply
Samsung 4C guidance asks for fully open model-required hot and cold supplies. Never infer that a valve is open from the control setting alone.
Inspect the supply hoses
Inspect visible hot/cold hose routing for swaps, kinks, pinches, damage, or a Flood Safe device. Do not pull the washer hard or disconnect pressurized hoses.
Check drain-hose installation
Samsung lists improper drain-hose insertion and an airtight standpipe as possible contributors. Use the exact model installation manual; do not guess a height or remove the rear hose-retaining screw.
Check the inlet mesh filters
Samsung lists sediment at the inlet connections for 4C. Shut water off and disconnect power; check the exact model instructions before removing a hose or filter.
Open the water valves fully
Open the required household valves and verify hot/cold routing where applicable. Stop for a stuck valve or leak; a completed fill observation is needed before marking the issue fixed.
Correct the supply-hose problem
Correct only visible, safe hose routing or have a qualified installer do it. Restore water, check for leaks, and observe a normal fill attempt before continuing.
Correct the drain-hose position
Correct the external drain position only when the model manual confirms it and access is safe. Do not seal the standpipe airtight or remove the factory hose retainer.
Power-cycle once after recording the code and checking hoses
Samsung 4C guidance permits one minute without power after external hose checks. Record the code first, use only safely accessible power, and do not repeatedly clear a returning code.
Clean the inlet mesh filters
Clear only owner-accessible mesh debris, reconnect carefully, check for leaks, and complete one normal fill retest. Never probe an energized inlet valve.
External fill checks are exhausted
Report the exact returning code, model, supply and hose layout, drain position, one-minute reset result, screen access, and all incomplete checks. No failed valve, sensor, wiring, or control has been established.
Safe troubleshooting sequence
Start with the observations and external checks that can be verified without opening energized assemblies. The interactive version asks these in order and changes the path based on your answers.
- Separate a fill fault from normal sensingSamsung says weight sensing can delay visible filling; record an actual 4C/4E/nF code before any reset. If the model layout, displayed code, water condition, or safe access is unknown, choose Not sure. It records an unresolved check rather than a passed one.
- Start with the water supplySamsung says to confirm the faucets are open and hoses are connected correctly. If the model layout, displayed code, water condition, or safe access is unknown, choose Not sure. It records an unresolved check rather than a passed one.
- Inspect the supply hosesWrong connections, kinks, and pinches can trigger fill errors. If the model layout, displayed code, water condition, or safe access is unknown, choose Not sure. It records an unresolved check rather than a passed one.
- Check drain-hose installationIncorrect drain installation can contribute to siphoning or fill behavior. If the model layout, displayed code, water condition, or safe access is unknown, choose Not sure. It records an unresolved check rather than a passed one.
- Check the inlet mesh filtersSamsung says debris buildup in inlet screens can restrict water and trigger fill errors such as 4C. If the model layout, displayed code, water condition, or safe access is unknown, choose Not sure. It records an unresolved check rather than a passed one.
What the answers can lead to
Let the normal sensing phase finish
A short delay before water enters is not by itself a failed fill system.
Evidence strength: Strong
Open the water valves fully
Samsung's fill troubleshooting starts with fully open water supplies.
Evidence strength: Strong
Correct the supply-hose problem
Kinked, pinched, damaged, or incorrectly connected hoses are manufacturer-listed causes of fill errors.
Evidence strength: Strong
Correct the drain-hose position
Improper drain installation can interfere with proper fill behavior.
Evidence strength: Strong
Power-cycle once after recording the code and checking hoses
Samsung's 4C guidance includes one minute without power after external hose corrections; a reset does not repair a returning fault.
Evidence strength: Strong
Clean the inlet mesh filters
Samsung specifically identifies clogged mesh screens as a cause of restricted filling and fill errors.
Evidence strength: Strong
When professional diagnosis is the safer next step
If documented supply, hose, drain, reset, and accessible-screen checks do not restore filling, no failed part has been identified; model-specific service is next.
Appliance Verdict stops before energized electrical testing, gas-system work, sealed-system work, and other checks that can create unnecessary risk. A technician can use the model, issue, and completed checks from the interactive diagnostic as a starting point.
Repair or replace?
A diagnosis and a repair decision are different questions. Once you have a real repair quote, compare the total repair cost with the all-in price of a comparable replacement. Warranty or protection-plan coverage, appliance age, reliability history, efficiency, and likely future repairs can all matter. Appliance Verdict's interactive result includes a transparent cost comparison rather than a black-box replacement recommendation.
Manufacturer sources
Samsung Support · Samsung Support
Dataset reviewed through 2026-09-11. Appliance Verdict is independent and is not endorsed by the manufacturers cited. Always follow the exact owner or service documentation for your model.
Browse reviewed washer error codes →
Compare this symptom across supported brands →
Browse all Samsung troubleshooting guides →